df005m-g thru df10m-g features - plastic package used has underwriters laboratory flammability classification 94v-0 - glass passivated chip junction - high surge overload rating of 50 amperes peak - high temperature soldering guaranteed: 260c/10 seconds, at 5 lbs. (2.3kg) tension mechanical data - case: molded plastic body over passivated junctions - terminals: plated leads solderable per mil- std-750, method 2026 - mounting position: any - weight: 0.014 oz., 0.4 g single-phase bridge rectifiers www.comchiptech.com comchip mds0312008a page 1 reverse voltage: 50 to 1000v forward current: 1.0a 0.315 (8.00) 0.285 (7.24) 0.013 (3.3) 0.0086 (0.22) 0.350 (8.9) 0.300 (7.6) 0.255 (6.5) 0.245 (6.2) 0.335 (8.51) 0.320 (8.12) 0.080 (2.03) 0.050 (1.27) 0.023 (0.58) 0.018 (0.46) 0.185 (4.69) 0.150 (3.81) 0.130 (3.3) 0.120 (3.05) 0.075 (1.90) 0.055 (1.39) 0.205 (5.2) 0.195 (5.0) dimensions in inches and (millimeters) df-m 0.045 (1.14) 0.035 (0.89) maximum ratings & thermal characteristics ratings at 25? ambient temperature unless otherwise specified. df df df df df df df parameter symbo l 005m-g 01m-g 02m-g 04m-g 06m-g 08m-g 10m-g unit device marking code df005 df01 df02 df04 df06 df08 df10 maximum repetitive peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v max. average forward output rectified current at t a =40? i f(av) 1.0 a peak forward surge current single sine-wave superimposed on rated load (jedec method) i fsm 50 a rating for fusing (t < 8.3ms) i 2 t10a 2 sec typical thermal resistance per leg (note 1) r ja 40 r jl 15 ?/w operating junction and storage temperature range t j , t stg 55 to +150 ? electrical characteristics ratings at 25? ambient temperature unless otherwise specified. df df df df df df df parameter symbo l 005m-g 01m-g 02m-g 04m-g 06m-g 08m-g 10m-g unit maximum instantaneous forward voltage drop per leg at 1.0a v f 1.1 v maximum reverse current t a = 25? 5.0 at rated dc blocking voltage per leg t a = 125? i r 500 a typical junction capacitance per leg at 4.0v, 1mhz c j 25 pf note: (1) thermal resistance from junction to ambient and from junction to lead mounted on p.c.b. with 0.5 x 0.5" (13 x 13mm) copper p ads
single-phase bridge rectifiers www.comchiptech.com comchip mds0312008a page 2 0.4 0.6 0.8 1.0 1.2 1.4 0.01 0.1 1 10 1 10 100 1 10 100 20 40 60 80 100 120 140 150 0 0.5 1.0 1 10 100 0 10 20 30 40 50 60 0 20 40 60 80 100 0.01 0.1 1 10 100 0.01 0.1 1 10 100 0.1 1 10 100 fig. 1 - derating curve output rectified current fig. 2 - maximum non-repetitive peak forward surge current per leg fig. 4 - typical reverse leakage characteristics per leg fig. 6 - typical transient thermal impedance fig. 3 - typical forward characteristics per leg fig. 5 - typical junction capacitance per leg average forward output current (a) average forward output current (a) instantaneous reverse current ( a) transient thermal impedance ( c/w) instantaneous forward current (a) junction capacitance (pf) ambient temperature ( c) number of cycles at 60 hz percent of rated peak reverse voltage (v) t, heating time (sec.) instantaneous forward voltage (v) reverse voltage (v) 60 h z resistive or inductive load p.c.b mounted on 0.51 x 0.51" (13 x 13mm) copper pads with 0.06" (1.5mm) lead length t j = 25 c pulse width = 300 s 1% duty cycle t j = 150 c single sine-wave (jedec method) t j = 25 c f = 1.0mhz vsig = 50mvp-p 1.0 cycle t j = 125 c t j = 25 c ratings and characteristic curves (t a = 25? unless otherwise noted)
|
